- #Drb3 emulator on sprinter install#
- #Drb3 emulator on sprinter update#
- #Drb3 emulator on sprinter Offline#
I already called my locksmith, who drives an 04 Sprinter to try it as well. I already tested it on a 2010 Charger under witech and works flawlessly, and got a 2004 Dodge pickup and under the emulator worked perfectly. When green LED turns on, turn on car ignitionĢ4: When Windows is done installing drivers, etc, you should show a network connection in the tool tray with no internet accessĢ6: Press “Launch DRB III” button in lower right hand corner Do NOT update WiTech!!!ġ6: Flexnet will find updates for enhanced DRB and K-LineĢ0: Once updates and downloaded and installed, turn OFF internet and NEVER turn on again!Ģ2: Attach Micropod to car.
#Drb3 emulator on sprinter install#
These are the steps I followed to get Enhanced DRB III Emulator to work:ġ: Make a backup copy of the partition from the hard drive included with the micropod!ģ: Set date to 01/01/17 BEFORE booting from laptopĥ: Allow windows to install drivers, etc, as needed for your laptop and reboot as needed.Ħ: Once all of that is done, do NOT run WiTech yet!Ĩ: Navigate to C:\ProgramData\wiTECH\jserver\data\core\stubsġ5: Run Flexnet software updater.
![drb3 emulator on sprinter drb3 emulator on sprinter](https://media.fotki.com/1_p,rtrtqktqwskbkdfxdbsfktqggtqb,vi/bsfsskdbqxbrwrrbfqwxbrstgdrkk/0/1043660/13076656/02ID-vi.jpg)
So if you need one for online use this is not the unit to buy.
#Drb3 emulator on sprinter Offline#
The device I purchased is an OFFLINE ONLY version of micropod 2, but I only use it for diagnostics, not for programming as I do not have a TechAuthority account. Once updated, disconnect the internet and change the date back to 1/1/17 for it to work. So the instructions are good, but at least for me, I had to fix the date to the correct date to get the flexnet updates. Plugged in the pod, waited for windows to see it and make the virtual network, and then launched wiTech. Then I followed the rest of the instructions. As soon as both had updated, I disconnected internet and then changed date back to 1/1/17.
#Drb3 emulator on sprinter update#
Now flexnet connect worked and I was able to update K-line and enhanced drb3. the wi-tech software is a fantastic tool if you service any chrysler product out there, the ability to see all modules that are online as well as the communication lines in a very easy to view graphic, it also allows the tech to program directly from the application without additional software, system shows modules and checks software revisions. So I changed the date to the correct date. Windows update also errored because of the wrong date. Try to use flexnet connect to update but it failed. In the beginning when installing the stubs, his directions had already instructed you to change the date to 1/1/17, then navigate to the folder and install the three stubs. In order to get it to work, I had to change the date. I had to change it up since I did follow his instructions exactly, but the flexnet update didn’t work, and so it failed and the drb3 did not work. Anyway I will have to contact the seller and arrange for some discount since the hard drive is virtually useless.Īnyway, the main thing is that the miocropod 2 had the required circuits etc, and the DRB3 works after following most of Radius’s instructions.
![drb3 emulator on sprinter drb3 emulator on sprinter](https://cimg2.ibsrv.net/gimg/www.crossfireforum.org-vbulletin/1056x587/miscellaneous_functions_7dc764fc4efdf2e690088d73d46e8a30ac98add9.jpg)
![drb3 emulator on sprinter drb3 emulator on sprinter](https://www.obd2cartool.com/images/Mercedes_Benz_CR2_IMMO_Emulator_3502074_a.jpg)
I was able to make a backup though and there is actually a second partition on it with an Acronis backup image already created from 8/15/17. Its making beeping sounds and clicking and on its very last legs. It came with a hard drive that is barely working. I bought my miocropod 2 clone from, same as what Radius bought.